Size Guide
Understanding LAVIRAE Sizing
Description
xLift Heavy Tile, Glass, and Mirrors Solo — No Slips, No Scratches, No Buddy Required
Stop sweating through bare-hand lifts. The ProGrip™ Suction Lifter locks onto polished tile, tempered glass, mirrors, sealed stone, and sheet metal with a 118mm vacuum pad and an 8mm rubber gasket — strong enough to hold a heavy porcelain slab one-handed, soft enough to leave zero scuffs on a mirror finish.
Done With Bare-Hand Lifts, Cheap Cups That Pop, and the Fear of Dropping $80 in Tile?
Bare hands slip on polished faces. Plastic suction cups from the big-box aisle lose vacuum mid-lift with no warning. The two-guys-and-a-prayer method only works until your buddy cancels Saturday morning. You need a single airtight grip that holds tight from the press to the release — every lift, every time.
➤ 118mm Vacuum Pad That Bites and Holds: Press the pad flat, flip the cam lever, and the rubber gasket pulls a vacuum strong enough to hold heavy porcelain planks, tempered glass panels, and full-size mirrors one-handed.
➤ 8mm Rubber Gasket — Thick Enough to Grip, Soft Enough Not to Mark: Cushions polished finishes so there's no scuff, no suction ring, and no residue to wipe off when you release.
➤ All-Metal Body + ABS Cam Lever: 170mm yellow alloy frame won't flex under load. The 80mm cam throw locks in under a second — no thumb cramps, no half-stuck lever popping mid-lift.
How One Cam Lever Turns a Rubber Pad Into a Vise-Grip on Glass
Press the 118mm pad flat against any clean, non-porous surface — polished porcelain, tempered glass, sealed marble, sheet metal, finished plywood. Flip the 80mm cam lever and the rubber gasket deforms into a sealed pocket, pulling a partial vacuum that locks tight until you decide to release it.
The yellow alloy body holds its shape under load instead of flexing and breaking the seal. The 24mm knurled steel knob gives you fine-touch pressure control. The textured ABS lever stays grippy even when your hands are dusty from cement board or coated in tile adhesive — which is exactly when you need it to.
Why DIY Renovators and Weekend Tile Setters Reach For This Before They Reach For a Buddy
From bathroom remodels to backsplash installs to glass shower swaps — guys who used to need a second pair of hands now set big slabs solo with one of these in the bucket.
"I was about to text my brother-in-law to drive over and help me set a 30x60 porcelain plank. Pulled this out instead, set the slab solo in ten minutes. Saved my back and the tile." — Mike R., Phoenix AZ
What Changes the First Time You Use It
✓ Solo Lifts Get Easy: No more begging a buddy to come spot you on a Saturday. Slap the pad on, flip the lever, lift — done.
✓ Polished Surfaces Stay Pristine: The 8mm rubber gasket grips without scratching, scuffing, or leaving suction rings on glass, mirrors, or high-gloss tile.
✓ The Scary Part Stops Being Scary: When you trust the seal won't pop mid-lift, the hardest part of the install turns into the easiest.
How to Lock On a Vise-Grip Seal in 3 Steps
Step 1: Wipe the contact surface clean and dry — dust kills suction faster than a torn gasket.
Step 2: Press the rubber pad flat against the surface, then flip the cam lever all the way down to pull the vacuum seal.
Step 3: Lift, move, or hold in place as long as you need. Flick the lever back up to release with a soft pop — no scuff left behind.
| ProGrip™ Suction Lifter | Bare Hands + Gloves | Cheap Plastic Suction Cups |
|---|---|---|
| 118mm vacuum pad + all-metal body holds heavy slabs one-handed | ❌ Hands slip on polished faces, chip corners | ❌ Loses vacuum mid-lift with no warning |
| 8mm rubber gasket grips without scuffing glass or mirrors | ❌ Greasy fingerprints all over the finish | ❌ Hard plastic rims leave suction rings |
| Metal frame + ABS cam lever locks in under a second | ❌ Two-person job — and your buddy never shows | ❌ Snaps after two or three jobs |
Specs for the Detail-Oriented
- Color: Yellow powder-coated metal body
- Dimensions: 6.7 in length × 4.3 in height (170mm × 110mm)
- Suction Pad: 4.6 in diameter (118mm) with 0.31 in (8mm) rubber gasket
- Cam Lever: 3.1 in (80mm) throw, textured ABS grip
- Materials: Metal alloy body, ABS lever, rubber gasket
- Includes: 1 ProGrip™ Suction Lifter
Questions? Here's What You Really Need to Know
Will it hold a heavy porcelain plank without the seal popping mid-lift?
Yes — on clean, smooth, non-porous surfaces the 118mm pad pulls a strong vacuum that holds heavy tile, glass, sealed stone, and sheet metal. Wipe the surface dust-free before sealing for max grip.
Will the rubber leave marks on polished glass or a mirror finish?
No. The 8mm rubber gasket is soft enough to seal cleanly — you get a clean release with no suction ring or residue, even on high-gloss tile and polished glass.
Does it work on textured tile, raw stone, or porous surfaces?
It needs a smooth, non-porous face to pull a tight vacuum — polished porcelain, sealed marble, glass, metal, and finished plywood all work. Heavily textured stone, raw concrete, or unsealed porous tile won't hold the seal.
Is the body actually metal, or is it metal-colored plastic?
Real metal alloy — that's the yellow main body in the photos. The cam lever is reinforced ABS plastic for grip and durability, and the gasket is rubber. No painted-plastic shortcuts.
How do I release the seal without dropping the panel?
Brace the panel with your other hand or set it against a stable edge first, then flip the cam lever back up. The vacuum releases with a soft pop and the pad lifts away clean.
Stop Sweating the Lift. Start Setting Tile Like You've Done It a Hundred Times.
Grab the ProGrip™ Suction Lifter and the scariest part of your install becomes the easiest. No buddy needed. No scuffs on your $80 tile. Just a clean, controlled lift — every time you flip the lever.
- Choosing a selection results in a full page refresh.